Engineered mineral · Fired at 1200 °C
Sintered stone, 3200 mm wide and 6 mm thin
Mineral slabs with an inorganic binder, fired until the surface closes completely. Zero porosity, UV stable, heat resistant — and thin enough to clad a façade or build a 24 mm mitred worktop. CNAS certified, cut and drilled to your schedule in Yunfu, China. Send your drawings.
How sintered stone is made — and why that matters
The slab starts as a dry mix of mineral aggregates and pigments with an inorganic binder. It is pressed under high pressure, then fired at roughly 1200 °C. At that temperature the binder fuses the particles into a single body with no resin and effectively no open pore structure. What comes out is closer to ceramic glass than to stone, and it behaves accordingly: it does not absorb, it does not yellow in the sun, and it does not care about a hot pan.
This is the material that solved the two standing weaknesses of engineered quartz — heat and UV — without giving up the non-porous surface. It is not, however, a magic material. It is brittle in thin sections, it chips at an unsupported edge, and it cannot be repaired by polishing a scratch out the way solid surface can. Knowing that at the design stage is what makes a sintered stone project go smoothly.
Technical data
| Property | Typical value | What it means in practice |
|---|---|---|
| Composition | Mineral aggregate + inorganic binder | No resin — no UV yellowing, no heat marking |
| Firing | ≈1200 °C | Fully vitrified surface |
| Water absorption | ≈0% | No sealing ever; safe in wet and food-contact areas |
| Mohs hardness | 6–7 | Resists knife marks and daily abrasion |
| Heat resistance | Excellent, no trivet needed | Hot pans, grills and oven trays are acceptable |
| UV stability | Stable | Suitable for outdoor kitchens and façades |
| Thickness we fabricate | 6 / 12 / 20 mm | 6 mm cladding, 12 mm mitred worktops, 20 mm heavy duty |
| Max slab | 3,200 × 1,600 mm | Full-height shower walls and island tops in one piece |
CNAS test report supplied with the shipment. Ask for the report for your specific colour and thickness.
The four applications that justify the cost
Sintered stone is not the cheapest option per square metre, so it pays to use it where its specific properties are doing work:
- Outdoor kitchens and BBQ islands — the combination of UV stability and heat tolerance is unmatched, and no sealer cycle is required.
- Ventilated façades and exterior cladding — 6 mm panels are light enough for bracket systems and will not fade.
- Full-height shower walls — 3,200 mm means a wall without a horizontal joint, and zero absorption means no sealing behind the glass.
- Thin, mitred furniture — a 12 mm top mitred to a 24 mm edge gives the weight of solid stone at half the mass, which is what stone furniture needs.
How we fabricate sintered stone
Sintered stone is cut on waterjet and CNC with diamond tooling, then edges are mitred and bonded with a colour-matched adhesive rather than laminated. Because the material is thin and brittle, every piece is supported on a full bed during handling and transport, and drilled holes are positioned to avoid stress paths. Internal corners are radiused, never squared — a square internal corner is where these slabs crack.
Finished pieces are crated vertically in A-frames with foam-rubber separation, labelled per the installation sequence, and photographed before the container is sealed. Lead time is three to four weeks per 20-foot container after deposit and drawing approval, EXW, FOB or CIF.
Related surfaces
Sintered stone FAQ
Quartz is bound with polymer resin, so it is heat sensitive and not UV stable. Sintered stone uses an inorganic binder fired around 1200 °C, giving zero porosity, full UV stability and heat resistance. Sintered stone is also available far thinner — 6 mm against a practical minimum of 20 mm for quartz.
We routinely fabricate 6 mm for wall cladding and cabinet fronts, 12 mm for furniture and worktops with mitred edges, and 20 mm for heavy-duty kitchen and outdoor surfaces. A 12 mm top mitred at 45 degrees reads as a 24 mm solid edge.
It is scratch and heat resistant but not impact-proof. A heavy blow to an unsupported edge or corner can chip, and a large thin panel needs a fully supported substrate. We recommend 20 mm or a continuous substrate wherever the surface will take knocks.
Yes. Because it is UV stable, frost resistant and non-porous, 6 mm panels are used for ventilated façades and exterior cladding. We cut and drill to your fixing schedule and can supply panels pre-drilled for the bracket system you specify.
Large format job? Send the panel schedule
Share the drawings, fixing details and exposure. We confirm thickness, edge treatment and lead time within 24 hours.
